Home cellar · practical guide
Most wine faults (turning to vinegar, mould and "mousy" smells, Brettanomyces) start in dirty vessels and tools. How to clean and sanitise a qvevri, a demijohn, a barrel and bottles; what metabisulphite, citric acid, soda, percarbonate and lime are, how much you need, and what must never be used.
Clean first, then sanitise: a sanitising solution does not work on dirt, lees or tartrate. Always add the chemical to the water, not the other way round, and work with gloves. The number of spoons is approximate; scales are better.
Water and chemical amounts are calculated from the capacity: a small vessel is partly filled and rolled, a large one (qvevri, barrel) is worked with a brush and a small amount of solution. The sulphur dose is approximate (≈ 2 g per 100 L of capacity).
What it is: A white powder that releases SO₂ in water and wine (57.6% of its mass).
What for: Sanitising vessels and tools (with citric acid); protecting must and wine.
Dose: Sanitising: 10 g/L + 5 g/L citric acid. In wine: 0.1 g per 10 L ≈ 6 mg/L SO₂.
Safety: SO₂ gas is dangerous for asthmatics: work outdoors and do not sniff the solution. Store dry and tightly closed.
Where to buy: Winemaking supply shop. Sodium metabisulphite (Na₂S₂O₅) is cheaper but adds sodium to wine: use it only for vessels.
What it is: A food acid, white crystals.
What for: Strengthening the sulphite solution (it lowers the pH); neutralising alkali residue; removing deposits.
Dose: With sulphite: 5 g/L. Rinse after alkali: 5–10 g/L.
Safety: Irritates the eyes. Mixed with sulphite it releases SO₂ gas.
Where to buy: Grocery shop, winemaking supply shop.
What it is: A compound of soda and hydrogen peroxide; it releases oxygen in water. Sold as "oxygen bleach".
What for: Washing glass, steel, plastic and bottles; removing colour and smells.
Dose: 3–10 g/L in water at 40–60 °C; 30 minutes to overnight.
Safety: Dries the skin and harms the eyes: use gloves. Careful with oak barrels: it bleaches the wood.
Where to buy: Winemaking supply shop; in a household shop only the pure product, without fragrance or additives.
What it is: Washing soda, a strong alkali. Do not confuse it with baking soda (NaHCO₃), which is much weaker.
What for: Dissolving tartrate and lees; washing barrels, qvevri, steel.
Dose: 10–20 g/L in water at 50–70 °C.
Safety: Harms skin and eyes: goggles and gloves. Always rinse with acid afterwards.
Where to buy: Household shop, winemaking supply shop.
What it is: The traditional Georgian agent for washing qvevri; a strong alkali.
What for: Washing and sanitising a qvevri with a brush.
Dose: 10–30 g/L (milk of lime), then plenty of clean water.
Safety: Very dangerous for the eyes: goggles are essential. Burns the skin.
Where to buy: Building supplies shop (pure, without additives), market.
What it is: Releases SO₂ gas when burned.
What for: Sanitising and storing empty qvevri and barrels.
Dose: ≈ 2 g per 100 L of capacity; in storage every 1–2 months.
Safety: The gas is highly toxic: do not breathe it in or put your head into the vessel. Fire hazard.
Where to buy: Winemaking supply shop, agricultural shop.
What it is: A solution of ethanol in water.
What for: Sanitising small tools, taps, stoppers and hands by spraying.
Dose: Undiluted, as a spray; 1–2 minutes.
Safety: Flammable.
Where to buy: Pharmacy.
With wood, corks and wine phenolics it forms chlorophenols and TCA, the musty "corked" smell that never leaves the vessel. It also corrodes steel. Mixed with acid it releases toxic chlorine gas.
Leaves fragrance and a thin film that spoils the taste of wine and kills the foam of sparkling wine. If you use it, rinse many times.
Brings in vinegar bacteria and the smell of ethyl acetate, wine's main enemy.
Leaves scratches on plastic, enamel and steel in which bacteria hide.
Very effective, but it burns skin and eyes severely and dissolves aluminium. At home soda ash and percarbonate are enough.
Wine is a fairly hostile environment for microbes: it is acidic and contains alcohol and SO₂. Some microbes still manage to live in it. Vinegar bacteria (Acetobacter) turn alcohol into vinegar when oxygen is present. Brettanomyces gives wine "horse", "barnyard" and "sticking plaster" smells. Some strains of lactic acid bacteria cause "mousy" smells, ropiness and haze. Moulds saturate vessels and stoppers with a mouldy smell that passes into the wine.
These microbes almost always get into the wine from vessels, hoses, funnels and hands. Most of the wine that spoils at home is spoiled not by bad grapes but by badly washed vessels. Cleanliness is cheap; a spoiled wine often cannot be put right.
Cleaning removes dirt, lees, tartrate, colour and smell from a surface. Alkaline agents are used for this: soda ash, percarbonate, lime. They dissolve proteins, phenolics and tartrate. Sanitising kills the microbes left on the surface: an acidified sulphite solution, sulphur gas or alcohol is used for this.
The order is always the same: clean first, then rinse, then sanitise. A sanitiser cannot get through a layer of dirt: microbes under lees are protected. That is why "sulphiting" a dirty vessel achieves nothing.
| Stage | Purpose | Agent |
|---|---|---|
| Cleaning | Removing dirt, lees, tartrate | Soda ash, percarbonate, lime (qvevri), hot water, brush |
| Rinsing | Neutralising alkali residue | Citric acid, then clean water |
| Sanitising | Killing microbes | Sulphite + citric acid, sulphur gas, 70% alcohol |
| Storage | Protecting an empty vessel | Drying, burning sulphur (qvevri, barrel) |
Potassium metabisulphite (K₂S₂O₅) dissolves in water and releases sulphur dioxide, 57.6% of its mass. In water SO₂ exists in three forms: molecular SO₂, the bisulphite ion (HSO₃⁻) and the sulphite ion (SO₃²⁻). Only the molecular form kills microbes, because it passes through the cell membrane. The share of the molecular form depends on pH:
$$SO_2^{\text{mol}} = \frac{SO_2^{\text{total}}}{1 + 10^{\,pH - 1.81}}$$
A metabisulphite solution in plain water has pH ≈ 4.5: only ≈ 0.2% of the SO₂ is molecular. Citric acid lowers the pH to ≈ 3, and molecular SO₂ increases ≈ 20 times. That is why acid is always added to a sanitising solution: the standard solution is 10 g/L metabisulphite and 5 g/L citric acid. Such a solution kills yeasts and bacteria on a clean surface in 5–10 minutes.
After the sulphite solution the vessel is not rinsed with water: plain water would leave microbes on the surface again, while the thin film of sulphite adds a few mg/L of SO₂ to the wine, which is harmless. The solution keeps for 2–3 weeks in a closed bottle; when you can no longer smell it, replace it.
Sodium metabisulphite (Na₂S₂O₅) works the same way and is cheaper, but sodium is undesirable in wine. It can be used for sanitising vessels, but not for adding to wine.
Wine residues (lees, a film of phenolics and proteins, tartrate, i.e. potassium bitartrate) are acidic by nature and dissolve well in alkali. That is why vessels are washed with alkali.
Soda ash (washing soda), Na₂CO₃, is a strong alkali (a 1% solution has pH ≈ 11.5). It converts tartrate into a soluble salt and removes phenolics and proteins. Baking soda (NaHCO₃) is much weaker and is only good for removing smells.
Sodium percarbonate (2Na₂CO₃·3H₂O₂) breaks down in water into soda and hydrogen peroxide. The peroxide releases oxygen, which oxidises organic dirt, colour and smells, while the soda dissolves residues. It is especially effective in warm water (40–60 °C) and is the best cleaner for glass, steel and plastic.
Slaked lime, Ca(OH)₂, is the traditional Georgian agent for washing a qvevri. Milk of lime (lime in water) is brushed onto the walls of the qvevri: the alkali kills microbes and dissolves tartrate. Lime does not harm the qvevri's beeswax lining. After liming, the qvevri is rinsed many times with clean water until the last water is neutral.
Alkali residue harms wine: it lowers the acidity, raises the pH, browns the colour and gives a soapy taste. So after washing with alkali the vessel is rinsed first with water, then with weak citric acid (5–10 g/L), which neutralises any remaining alkali. To check the last rinse water use pH paper or phenolphthalein: in alkaline water phenolphthalein turns pink.
Empty qvevri and barrels are traditionally treated by burning sulphur. When it burns, sulphur turns into SO₂ gas:
$$S + O_2 \rightarrow SO_2$$
1 gram of sulphur gives ≈ 2 g of SO₂. The gas fills the vessel, dissolves on the damp surface and kills microbes. Sulphur is burned in two situations: before filling with wine (sanitising) and to store an empty vessel, in which case it is repeated every 1–2 months. The sulphur is burned on a special holder so that no residue drops into the vessel: drops of burnt sulphur give wine a hydrogen sulphide ("rotten egg") smell. The dose is about 2 g of sulphur per 100 L of capacity; excess sulphur stays in the walls of a qvevri or barrel and adds extra SO₂ to the wine.
SO₂ gas is highly toxic. Do not put your head into a sulphured vessel, and do not climb into a qvevri or a deep tank until it has been well ventilated: CO₂ also collects in a closed vessel.
Glass, stainless steel and intact enamel are smooth and inert: microbes cannot hide on their surface and every agent can be used. Chlorine and hydrochloric acid must never be used on steel: it corrodes and pits. Do not wash enamel with abrasives.
Plastic is soft: bacteria live in scratches, where cleaning agents cannot reach. Plastic also absorbs smells. So plastic is washed only with a soft sponge, very hot water (above 80 °C) is avoided, and a plastic vessel that smells of vinegar or mould is no longer used for wine.
Oak is porous: wine and microbes penetrate several millimetres into the wood. An oak barrel is washed with hot water and soda, rinsed with acid and stored with sulphur. Never leave an empty barrel without sulphur, and soak a dried-out barrel with water before use until the wood swells. A barrel that has picked up a smell of vinegar or Brettanomyces often cannot be saved.
A qvevri is lined inside with beeswax. The wax closes the pores and makes cleaning easier. Hot water and strong solvents damage the wax lining, so a qvevri is washed with cold water, lime and a brush. If a qvevri has lost its wax lining or has developed a crack, it should be repaired by a qvevri maker.
Chlorine bleach should not be in a wine cellar at all. With wood, corks, cardboard and wine phenolics, chlorine forms chlorophenols, which moulds convert into 2,4,6-trichloroanisole (TCA). TCA is the "corked" smell of wet cardboard and cellar mould, which can be detected in wine at a few nanograms per litre. Once a cellar, barrel or qvevri has been contaminated, it is almost impossible to get rid of. In addition, when chlorine is mixed with acid (for example with a sulphite solution) it releases toxic chlorine gas.
Washing-up liquids leave fragrance and a film of surfactants. Vinegar brings vinegar bacteria into the wine. Caustic soda (NaOH) is effective but too dangerous for home use.
Always add the chemical to the water, not the other way round, especially alkalis, which heat up as they dissolve. Work with gloves and goggles: lime and soda ash are very dangerous for the eyes. If any gets into your eyes, rinse immediately with water for 15 minutes and see a doctor. Prepare sulphite solutions and burn sulphur outdoors or in a well-ventilated room; SO₂ is especially dangerous for people with asthma. Never mix chlorine with acid, or chlorine with sulphite. Keep chemicals in labelled, tightly closed containers, away from food and children.
1. In the "Making up a solution" mode choose the agent and enter the amount of water. You will see how many grams (and roughly how many spoons) of the agent you need, what water temperature, for how long, and what to do afterwards. You can change the concentration, and the calculator will tell you whether it is too weak or stronger than needed.
2. For the sulphite solution the chart shows how molecular (microbe-killing) SO₂ increases as citric acid is added. For the other agents the chart shows how many grams are needed for different amounts of water.
3. In the "Treating a vessel" mode choose the vessel type, capacity (for bottles, the number) and condition: new, clean and being prepared for filling, just emptied, or smelling bad. You get a list of steps, each with water and chemical amounts, time and an explanation. The cards at the top show the total water, chemicals and time.
4. The "Chemicals" mode describes each agent: what it is, what it is for, at what dose, how to use it safely and where to buy it. Below it is a list of what must not be used.
• Everything that touches wine (vessels, hoses, funnels, ladles, taps, stoppers) must be sanitised before use and washed after use.
• Wash a vessel immediately after emptying it. Dried lees are much harder to remove and become a breeding ground for vinegar bacteria.
• After use, flush a hose with hot water and soda, hang it up and let it dry. If you see stains or deposits inside a clear hose, replace it: hoses are cheap.
• Store empty qvevri and barrels with sulphur and with the mouth covered. Store empty demijohns and steel tanks dry and covered with paper.
• The cellar should be clean and dry: do not store fruit, vegetables, vinegar or sauerkraut in it, because they attract vinegar bacteria and flies. Wipe up wine spilled on the floor straight away.
• Fruit flies (Drosophila) carry vinegar bacteria. Keep vessels covered at all times; during fermentation cover the pomace cap with a clean cloth.
• Sanitise your hands with alcohol before touching the wine or the inside of a vessel.
• Keep a bottle of sulphite solution ready for quickly wetting a ladle, funnel or tap.
• If a washed vessel still smells unpleasant, repeat the treatment: soaking overnight with percarbonate often helps.
• Hard deposits (tartrate) inside a glass demijohn dissolve in hot soda solution; sand or rice grains shaken with water remove them mechanically.
• A plastic drum, oak barrel or qvevri that still smells strongly of vinegar or mould will spoil the wine. Replace the plastic; for oak or a qvevri, ask an experienced winemaker or a qvevri maker for advice.
1. Why is citric acid added to a sulphite sanitising solution?
The molecular share of SO₂ rises quickly as the pH falls: without citric acid the solution has pH ≈ 4.5, with it ≈ 3, and there is ≈ 20 times more molecular SO₂.
2. You have just rinsed a demijohn after racking. Why is a sulphite rinse not enough if there is still a layer of lees on the bottom?
Sanitising works only on a clean surface: microbes under a layer of lees and tartrate are protected. Clean first, then sanitise.
3. Why must chlorine bleach not be used on wine vessels?
TCA can be smelled in wine even at nanogram levels. A wooden barrel or qvevri contaminated once can be ruined for good.
4. You have washed a qvevri with lime. What must you do before filling it with wine?
Lime is an alkali: its residue lowers the wine's acidity, raises its pH and spoils its taste. Test the last rinse water with pH paper or phenolphthalein.