Winemaking Laboratory
The qvevri method / Making a qvevri

Chapter V · The qvevri method

Making a qvevri

How a qvevri maker makes a qvevri: choosing the clay, building it by hand layer by layer, drying, a week-long firing, finishing with wax and lime. How much clay, wax and firewood it takes and how long the whole process lasts.

Qvevri

The qvevri shape is modelled as a surface of revolution: the widest part is at ≈ 60% of the height and the base is pointed. Clay density after firing ≈ 1.9 g/cm³; raw clay is ≈ 18% heavier (water and organic matter). Wax ≈ 0.3 kg/m² (a thin layer plus what soaks into the pores). One layer ≈ 17.5 cm: the master builds one such layer a day. All figures are approximate.

Height × diameter—m
Clay—kg
Beeswax—kg
Qvevri weight—kg

Calendar

From the experience of qvevri makers, building takes roughly 30 + 30·V days (V in m³): ≈ 6–8 weeks for 1000 L, ≈ 3 months for 2000 L; drying 3–4 weeks; firing 5–8 days. A qvevri is made only in the warm months: in the cold the clay does not dry and cracks in the kiln.

Building—days
Drying—days
Ready—
In total—days

Kiln

Firing stages: up to 200 °C, removing residual water (slowly, or steam cracks the clay); 450–600 °C, removing the chemically bound water of the clay minerals and the quartz transformation at 573 °C (the volume changes abruptly, so slowly); 800–1000 °C, sintering. Energy: heating the clay (0.9 kJ/kg·K) + bound water (≈ 0.4 MJ/kg) + residual water; firewood ≈ 15 MJ/kg, 500 kg/m³. Wax (melting point 62–64 °C) is applied when the wall is ≈ 70–100 °C.

Energy—MJ
Firewood—kg
Wax "window"—
Critical stages—

The qvevri and the qvevri maker

A qvevri is a large, egg-shaped clay vessel in which wine ferments, matures and is stored. It is buried in the ground up to its neck. The traditional Georgian qvevri winemaking method was inscribed on UNESCO's list of Intangible Cultural Heritage in 2013. The qvevri craftsman is called a mekvevre, and the craft is passed down through families from generation to generation. Today qvevri are made in the traditional way in only a few villages: Vardisubani (Kakheti), Makatubani, Shrosha, Tq'emlovana and Chkhiroula (Imereti), and Atsana (Guria).

A qvevri is made entirely from natural materials: unglazed clay, beeswax inside and a lime coating outside. Making a large qvevri takes months, and it is only done in the warm season.

Clay

Not every clay is suitable for a qvevri. Qvevri makers take clay from particular places and often blend several types. Qvevri clay must be plastic enough for the layers to fuse completely, yet must not shrink too much or crack during drying and firing. So the clay must also contain particles of sand, limestone and other coarser minerals. Clay minerals (kaolinite, illite, montmorillonite) contain different amounts of chemically bound water, which is released during firing. Iron oxides give the fired qvevri its red-brown colour.

The clay is first dried, crushed, soaked in water and cleaned of foreign matter, then kneaded for a long time until it becomes uniform and plastic.

Building

A qvevri is not made on a wheel: it is built by hand, layer by layer. The qvevri maker lays thick coils (ropes) of clay on top of each other, kneading and smoothing them by hand and with wooden tools so that each new layer fuses completely with the one below. Only 15–20 cm of height can be added in a day: the lower part must first harden to bear the weight of the layer above, so there is a day's rest between layers. Building a large qvevri therefore takes weeks or months: about 6–8 weeks for 1000 litres, about three months for 2000 litres. A master usually works on several qvevri at once.

The qvevri's shape (a narrow, pointed base, a wide belly and a short neck) serves both strength and winemaking: natural convection arises in the vessel during fermentation, while the lees collect in the narrow base and touch the wine less.

Drying

The finished qvevri dries slowly, in the shade, for 3–4 weeks. If it dries too fast, the surface shrinks before the inside and cracks appear. Clay shrinks by a few per cent as it dries. At this stage most of the water evaporates, but some moisture still remains in the clay's pores. In the cold, clay does not dry well, one of the reasons why qvevri are made only in the warm months.

Firing

The dried qvevri are stood in a large, vaulted kiln, the kiln entrance is bricked up, and the fire is kept burning without a break for 5–8 days. The temperature rises slowly and at its peak reaches roughly 900–1000 °C. The master judges when firing is finished by the colour of the flame and of the qvevri.

Slow heating is essential, because several physical and chemical changes take place in the clay:

TemperatureWhat happensWhy slowly
100–200 °Cevaporation of the water left in the poreswith fast heating, steam cracks the clay from within
300–500 °Cburning of organic matteroxygen must reach deep into the wall
450–600 °Crelease of chemically bound water from the clay mineralsthe clay loses mass and shrinks
573 °Cα-quartz turns into β-quartzthe volume changes abruptly, creating stress in a thick wall
800–1000 °Csintering: particles fuse togetherthe clay hardens and its porosity falls

The energy the kiln needs is many times more than is needed to heat the qvevri itself: most of the heat is carried away by the kiln walls, the air and the smoke. That is why several qvevri are fired together in one firing.

Wax and lime

After firing, while the qvevri is still warm (in a master's words, neither hot enough to burn your hand nor cold), melted beeswax is poured inside and the qvevri is rolled so that the wax covers the whole inner surface in a thin layer. Beeswax melts at 62–64 °C: on a warm wall it stays liquid and fills the pores and microcracks. The wax protects the wine from being absorbed too much into the clay, makes cleaning easier and is hygienic, although it does not completely close the clay's pores.

On the outside the qvevri is coated with lime slurry (sometimes a thin layer of cement): this strengthens the wall, covers small cracks and prepares the qvevri for burial. A well-made and properly maintained qvevri lasts for centuries.

Old and new qvevri

A new qvevri must be washed and treated several times before its first wine (see "Home cellar: hygiene"). An old qvevri that has stood empty for years or has developed a crack should be checked by a qvevri maker or an experienced winemaker: sometimes the qvevri is re-waxed, and damaged spots are filled with a special mixture.

How to use this page

1. In the "Size and materials" mode enter the qvevri capacity, the ratio of height to diameter, the width of the mouth and the wall thickness (the thickness fills in automatically when you change the capacity). You will see the qvevri's dimensions, the amount of clay (raw and fired) and wax needed, the number of layers, and the qvevri's weight, empty and full of wine. The chart shows a section of the qvevri, with its layers and the wine level.

2. In the "Making calendar" mode choose the start date and the qvevri capacity. The chart shows the stages (building, drying, firing, cooling, wax and lime) and when the qvevri will be ready. If any stage falls in the cold months, the calculation warns you.

3. In the "Firing" mode choose the peak temperature, firing time, number of qvevri in the kiln and the kiln efficiency. You will see the energy needed, the amount of firewood, the temperature curve with its critical stages, and the time when the qvevri should be waxed.

All figures are approximate and rest on a general physical model. Every qvevri maker works from his own experience, and his knowledge matters more than this calculation.

Buying a qvevri

• Order a qvevri directly from a qvevri maker: in Vardisubani, Makatubani, Shrosha, Tq'emlovana, Chkhiroula or Atsana. A large qvevri often has to be ordered months in advance.

• Inspect the qvevri: there should be no deep cracks on the surface, and the wax layer inside should be even. Tap it: a sound qvevri gives a clear, bell-like ring; a cracked one sounds dull.

• Transport the qvevri carefully, on a soft layer and secured. Before burial do not leave it for long in the sun or in frost.

• The qvevri is buried up to its neck, and earth or a sand-lime mix is packed around it layer by layer, so that it sits firmly and the weight of a full qvevri (more than a tonne) does not damage its walls.

• After burial and before the first wine, wash the qvevri several times with water and lime and check that it does not leak: fill it with clean water and check the level after a few days.

1. Why is a qvevri not made in winter?

Qvevri walls are thick and dry slowly. If moisture remains inside, steam cracks the clay from within during firing. That is why qvevri makers work only in the warm months.

2. Why is wax applied to a qvevri after firing while it is still warm?

Beeswax melts at 62–64 °C. On a warm wall it stays liquid, covers the whole surface as the qvevri is rolled, and fills the pores and microcracks.

3. Why is a qvevri heated slowly in the kiln, especially around 573 °C?

α-quartz turns into β-quartz at 573 °C and its volume changes by ≈ 1–2%. In a thick wall the temperature is uneven, so a fast transition causes stress and cracks.