Chapter V · The qvevri method
How much wine is in a qvevri and how to measure it with a stick; why a qvevri is waxed, how much wine the clay wall "drinks" and how much oxygen it lets through; and what the qvevri's egg shape gives: surface, lees and the pomace cap.
The exact capacity of a qvevri is best measured by filling it with water (by the bucket or with a meter). This calculation estimates the volume from a few measurements using a shape model: depth is measured with a straight stick, diameter with a folding rule or two sticks lowered inside. The table (a "dipstick scale") shows how much wine is in the qvevri according to the empty height.
Absorption: wine entering the clay pores = wall volume × porosity × penetration share (≈ 5% with wax, ≈ 30% with worn wax, ≈ 80% without wax). Oxygen through the wall: ≈ 0.5 with wax, ≈ 2 with worn wax, ≈ 6 mg/m²·day without wax (estimates; there are few measurements). The wall of a buried qvevri touches moist earth on the outside, which reduces oxygen further. For comparison: a new oak barrel (225 L) ≈ 20–40 mg/L per year.
In the narrow base of a qvevri the lees collect in a tall, narrow layer: their contact area with the wine is small. The surface-to-volume ratio (S/V) shows how much wall touches each litre of wine: a large qvevri "shows" the wine less wall. Pomace cap thickness = pomace volume ÷ the area of the wine surface near the top.
The qvevri (in western Georgia, churi) is a large clay vessel for wine, buried in the ground up to its neck. Qvevri come in different sizes, from a few tens of litres to several thousand; in a home cellar 500–2000 litres is most common. A qvevri combines three materials: a fired clay wall, a thin layer of beeswax inside and a lime coating outside. Each has its own function.
Fired clay is a ceramic: a rigid skeleton of mineral particles in which fine pores remain. Depending on the firing temperature and the clay composition, the porosity of qvevri clay is roughly 15–25%. The pores are micrometre-sized and draw in liquid by capillary force: without wax a qvevri absorbs a noticeable amount of wine into its wall, and this wine then oxidises and becomes food for microbes.
In a large qvevri the wall is a few centimetres thick. The thermal conductivity of clay (≈ 0.8–1.2 W/m·K) is far lower than that of metal, but the thermal regime of a qvevri is determined mainly not by the wall but by the surrounding earth (more on this on the "Fermentation in qvevri" and "Marani" pages).
The clay contains minerals of calcium, iron, potassium and other elements. Despite the wax layer the wine is partly in contact with the clay, and some researchers note a small influence of the clay on the mineral composition of qvevri wine. This question has not yet been fully studied.
Beeswax is a mixture of esters of long-chain fatty acids and alcohols, hydrocarbons and free fatty acids. It melts at 62–64 °C, does not dissolve in water or wine and is almost chemically inert: it gives the wine no taste or smell. In a qvevri the wax does three jobs:
1. It fills the pores and microcracks of the clay, reducing absorption of wine into the wall.
2. It creates a smooth surface that is easy to clean and gives microbes nowhere to hide.
3. It reduces (but does not completely stop) the movement of oxygen and moisture through the wall.
The wax layer wears away over time, especially with mechanical scrubbing and liming. So the qvevri is re-waxed from time to time, as needed: the qvevri is heated from inside (for example with fire or hot air) until the wall reaches 70–100 °C, and melted wax is brushed on in a thin layer.
On the outside the qvevri is plastered with lime or lime-cement. This layer strengthens the wall mechanically and protects the wall of the buried qvevri from outside moisture and soil microorganisms. When the qvevri is buried, earth or a sand-lime mix is packed around it layer by layer, so that the pressure of the full qvevri is borne not by the wall but by the surrounding earth. This matters: in a full 1000-litre qvevri the pressure on the wall near the base approaches 0.15 atmospheres, and an unburied clay wall can crack.
The egg shape of the qvevri brings several physical advantages:
• A curved surface distributes pressure evenly, as an eggshell does.
• During fermentation CO₂ bubbles rise in the centre and the wine sinks along the walls: natural circulation arises in the vessel, evening out temperature and contact with the pomace.
• In the narrow, pointed base the lees gather over a small area in a tall layer. The contact area between wine and lees is small, and the lees are disturbed less when the wine is drawn off.
• The narrow neck reduces the open surface of the wine: the surface touching the air or the pomace cap is small relative to the volume.
The surface-to-volume ratio (S/V) falls as size increases: a large qvevri "shows" the wine less wall per litre than a small one. So in a large qvevri the wine is in more stable conditions, while in a small qvevri the influence of the wall (oxygen, absorption) is greater.
A qvevri's nominal capacity is the maker's estimate and often differs from the real one by 10–20%. The exact capacity is found by filling it with water: by the bucket (of known volume) or with a water meter. It is convenient to make a "dipstick scale" at the same time: after every 10 buckets measure the empty height with a stick and write it down. With such a table you can find out at any time how much wine is in the qvevri. The calculator on this page does the same approximately, using a shape model.
1. In the "Volume and gauging" mode enter the qvevri's inner dimensions: depth from the rim to the bottom, maximum diameter, mouth diameter and the height at which the qvevri is widest. Then enter the empty height, the distance from the rim to the wine surface. You will see the qvevri's capacity, how much wine is in it, how many litres 1 cm corresponds to at the surface, and how full the qvevri is. The chart is a "dipstick scale".
2. In the "Wall" mode enter the qvevri capacity, wall thickness, state of the wax, clay porosity and how long the wine is kept. You will see how much wine the wall will absorb, how much oxygen will enter the wine through the wall and how much SO₂ it will use, and a comparison with an oak barrel.
3. In the "Shape" mode enter the capacity, shape, and the share of lees and pomace. You will see the surface-to-volume ratio (compared with other vessels), the height of the lees layer, the thickness of the pomace cap and the area of the wine surface.
• Depth: lower a straight wooden stick to the bottom in the centre of the qvevri, mark it at the level of the rim and measure.
• Maximum diameter: lower two sticks fastened together at one end and spread them in the widest part until they touch the walls; take them out and measure the distance between the ends. Or, if the qvevri is not yet buried, measure the circumference with a tape, divide by 3.14 and subtract twice the wall thickness.
• The widest point is usually at 55–65% of the depth from the bottom.
• The most accurate method is still filling with water. Do it once, when you wash the qvevri, and make your own scale.
• After each washing inspect the inner surface with a torch: if the wax has come off in many places and the clay shows through, the qvevri needs re-waxing.
• Use only pure, natural beeswax, without paraffin or other additives.
• Waxing requires heating the qvevri and is a fire hazard: do it the first time with the help of an experienced winemaker or qvevri maker. Ventilate the qvevri well before climbing into it.
• If the wine level drops in a new qvevri in the first weeks, the wall is absorbing it: keep the qvevri full with the same wine.
1. In a new, unwaxed qvevri the wine level gradually drops in the first weeks. Why?
Fired clay has a porosity of 15–25%. Without wax the wall absorbs a noticeable amount of wine. Wax fills the pores and almost stops absorption. That is why a new qvevri needs topping up.
2. Why is the base of a qvevri narrow and pointed?
In a pointed base the lees gather in a narrow "cone". The contact area between wine and lees is small, and the lees are hard to stir up when the wine is drawn off.
3. Which vessel "shows" the wine the least wall per litre?
The surface-to-volume ratio falls as size increases (∝ 1/R). In a large qvevri the wine interacts less with the wall and is in more stable conditions.